OTWapps
OTWapps
All apps
HomeSearch
Civil / Site
Full Site and Stormwater DesignPeak Runoff (Rational Method)Stormwater Runoff (TR-55)Earthwork Cut & FillGutter Spread & Inlet CapacityOutlet Structure RatingRiprap Outlet ProtectionGrass-Lined Channel & SwaleADA Ramp SlopeStorm Pipe SizingCulvert Capacity & SizingDetention Pond RoutingOpen-Channel FlowPavement DesignVertical CurvesSanitary SewerParkingFire Service LineModified Rational DetentionLift StationFull Lift Station Design
Structural
Wind Main Frame (MWFRS)Wind Components & Cladding (C&C)Load CombinationsLive LoadsWood BeamWood ColumnJoist & Rafter SpanSteel BeamSteel ColumnSeismic Base ShearSpread FootingCantilever Retaining WallTruss AnalysisSign StructuresSnow LoadsWood Shear Wall & DiaphragmConcrete VolumeRebar Weight & QuantityConcrete BeamCrane Runway BeamHelical Piles and AnchorsSolar Roof AttachmentTilt-Up Wall PanelSolar Ground-Mount PileFence and Freestanding Wall Wind
Electrical
Voltage DropPower Factor CorrectionDwelling Service LoadLighting (Lumen Method)Conductor Ampacity & SizingTransformer Size & ProtectionAvailable Fault CurrentBox FillConduit FillMotor Branch CircuitGrounding Conductor SizingPhotometric Analysis & Lighting LayoutPV String SizingConductor Resistance and Impedance
Mechanical
Duct SizingExhaustVentilationPsychrometricsHydronic Pipe Pressure DropPump and Fan PowerNPSH Available
Plumbing
Water Supply SizingDrain Fixture UnitsStorm/Roof DrainGas Pipe SizingWater Heater SizingSump Pump SizingWater Hammer (Surge)Pipe Thermal Expansion and Loop
Fire Protection
Sprinkler K-FactorSprinkler Design Area & DemandHydrant Flow Test & Supply CurveFire Extinguisher PlacementOccupant Load
AboutPricingAccount

Residential Load Calculator NEC 2023 Art. 220 Part III, standard method

NEC 2023 Art. 220

Result

Result not calculated

Confirm the inputs and the method notes before using the result.

How this result was calculated

Inputs & units
Method & assumptions
References & limitations
Engineering aid only. Professional verification required. The method notes and tags on this page are the references this app cites.

By running a calculation you agree to the Terms of Use and Privacy Policy. Results are preliminary and must be verified by a licensed professional.

Your calculation

▤Result not calculatedComplete the inputs and review before calculating.

Downloads

Review inputs, calculation steps, and assumptions in one report.

Code edition and design decisions (NEC 2023)

Code edition: NEC (NFPA 70) 2023. 2023 is the edition most US jurisdictions currently enforce, and adoption of the 2026 NEC is only starting. A later version of this app can add a 2026 option (the 2026 draft gives Annex D Example D1(a) as 18,075 VA versus 18,600 VA in the 2023 Annex D that this version reproduces). Every result here is NEC 2023 only.

  • Neutral: follows the Annex D Example D1(a) convention: range and dryer demand at 70% on the neutral (220.61(B)(1)); only 120 V appliances and motors you flag as neutral are counted; 240 V loads are assumed to have no neutral; neutral amperes over 200 A are taken at 70% (220.61(B)(2)). Neutral amperes are the neutral VA divided by 240 (two 120 V legs, as Annex D D1(a)), also on a 120/208 V service.
  • Heating and cooling (220.60): noncoincident by default, so the larger complete total governs (untick the box for a heat pump with supplemental strip heat). 25% of the largest motor (220.50 / 430.24) is added in both cases, even when the A/C motor is the largest motor but its load is the omitted one. This is a deliberately conservative choice: the 2023 text of 220.60 is ambiguous here, and read case by case (25% only of the largest motor actually in each case) the total is lower. The results show that case-by-case total and service size as an informational line.
  • Table 220.55 "major fraction": a fraction of 0.5 kW or more over 12 kW rounds up to the next whole kW (12.5 kW counts as 1 kW over) for the 5% per kW increase (Notes 1 and 2).
  • Line current: total VA divided by the service voltage (balanced single-phase 3-wire). Per-line (unbalanced) amperes as in Annex D Example D1(b) are not calculated.
  • Small appliances: fastened-in-place appliances under 500 VA are included at 100% and are not counted toward the "four or more appliances" test for the 75% factor (220.53).
  • Floor area (2023): from outside dimensions; garages and unfinished or unused space that can be converted to habitable or occupiable space are included; open porches are not (220.5(C), 2023 numbering).
  • Section numbers follow the 2023 renumbering (dwelling lighting 220.41, demand Table 220.45) as reported by secondary sources; confirm against the printed NEC.
  • Limits: one clothes dryer per dwelling unit (for two dryers, each counts 5000 VA or its nameplate, whichever is larger; adding both nameplates into the one dryer field is correct only when each is at least 5000 VA); the 125% continuous-load adder for EV charging and electric heating is not applied (the service rating is the calculated load only; size conductors and overcurrent devices separately).

Related apps

  • Voltage Drop
  • Power Factor Correction
  • Conductor Ampacity & Sizing
  • Transformer Size & Protection
  • Available Fault Current
  • All Electrical apps
OTWapps
About Methods & references View plans Privacy Terms

Engineering aid only. Professional verification required.