OTWapps
OTWapps
All apps
HomeSearch
Civil / Site
Full Site and Stormwater DesignPeak Runoff (Rational Method)Stormwater Runoff (TR-55)Earthwork Cut & FillGutter Spread & Inlet CapacityOutlet Structure RatingRiprap Outlet ProtectionGrass-Lined Channel & SwaleADA Ramp SlopeStorm Pipe SizingCulvert Capacity & SizingDetention Pond RoutingOpen-Channel FlowPavement DesignVertical CurvesSanitary SewerParkingFire Service LineModified Rational DetentionLift StationFull Lift Station Design
Structural
Wind Main Frame (MWFRS)Wind Components & Cladding (C&C)Load CombinationsLive LoadsWood BeamWood ColumnJoist & Rafter SpanSteel BeamSteel ColumnSeismic Base ShearSpread FootingCantilever Retaining WallTruss AnalysisSign StructuresSnow LoadsWood Shear Wall & DiaphragmConcrete VolumeRebar Weight & QuantityConcrete BeamCrane Runway BeamHelical Piles and AnchorsSolar Roof AttachmentTilt-Up Wall PanelSolar Ground-Mount PileFence and Freestanding Wall Wind
Electrical
Voltage DropPower Factor CorrectionDwelling Service LoadLighting (Lumen Method)Conductor Ampacity & SizingTransformer Size & ProtectionAvailable Fault CurrentBox FillConduit FillMotor Branch CircuitGrounding Conductor SizingPhotometric Analysis & Lighting LayoutPV String SizingConductor Resistance and Impedance
Mechanical
Duct SizingExhaustVentilationPsychrometricsHydronic Pipe Pressure DropPump and Fan PowerNPSH Available
Plumbing
Water Supply SizingDrain Fixture UnitsStorm/Roof DrainGas Pipe SizingWater Heater SizingSump Pump SizingWater Hammer (Surge)Pipe Thermal Expansion and Loop
Fire Protection
Sprinkler K-FactorSprinkler Design Area & DemandHydrant Flow Test & Supply CurveFire Extinguisher PlacementOccupant Load
AboutPricingAccount

Conduit Fill Calculator (NEC 2023 Chapter 9, Tables 1, 4, 5, 8, Notes 4 and 7)

Raceway and rules (all required except the size to check)
Conductors (one line per group: type, size, count [, name]; for type custom: custom, area in2, count [, name])
Advanced: full detailed inputs

Result

Result not calculated

Confirm the inputs and the method notes before using the result.

How this result was calculated

Inputs & units
Method & assumptions
References & limitations
Engineering aid only. Professional verification required. The method notes and tags on this page are the references this app cites.

By running a calculation you agree to the Terms of Use and Privacy Policy. Results are preliminary and must be verified by a licensed professional.

Your calculation

▤Result not calculatedComplete the inputs and review before calculating.

Downloads

Review inputs, calculation steps, and assumptions in one report.

Guide: OTW Conduit Fill (NEC 2023 Chapter 9, Tables 1, 4, 5, 8, Notes 4 and 7)
  1. Load an example to see the expected inputs, then replace every example value with your project data.
  2. Work through the input sections in order. Confirm the displayed units, selected method and applicable code.
  3. Use Detailed calculation inputs for additional settings and nested rows. Add or remove rows without editing code.
  4. Run the calculation, then review the governing check, assumptions, warnings and detailed results. Verify the result before using it in a design.
Code edition and design decisions (NEC 2023)

Code edition: NEC (NFPA 70) 2023, Chapter 9: Table 1 (53 % one conductor, 31 % two, 40 % over two), Note 4 (60 % for nipples 24 in. or less), Table 4 (raceway areas), Table 5 (insulated conductor areas), Table 8 (bare conductors, Note 8), Note 7 (rounding) and Annex C. Table values were compared across the 2017 NEC text and 2023-labelled reproductions. THW/THW-2/THHW at 14, 12, 10 and 8 AWG use 0.0139, 0.0181, 0.0243 and 0.0437 in2 (the 2017 text; RHH*/RHW*/RHW-2* have their own values). The EMT results are checked cell by cell (1360 cells, five insulation groups, the TW block for THW 14-8) against an NECA copy of Annex C Table C.1, which is the 2011 edition; THW 14-8 follow the 2017 text. All values are to be confirmed against the printed NFPA 70-2023 by a licensed reviewer.

  • Required inputs, no defaults: raceway type, nipple answer, rounding rule and the conductor list. Only the trade size to check is optional (blank = just find the smallest size).
  • Rounding rule (you choose): strict compares total conductor area with the Table 1 percent of the Table 4 area. note7 applies Note 7 to conductors that are all the same size and type (one group): a permitted count with a decimal of 0.8 or more is rounded up, which matches Annex C and can allow a fill slightly above the percent limit. Several lines of the same type and size (for example phases and neutral) are merged into one group first; different types or sizes are not. The fill percent is always shown and flagged on its own.
  • Conductor count for Table 1 is the total number of conductors entered, including an equipment grounding or bonding conductor (Note 3). Enter it as its own line. A multiconductor cable counts as one conductor (Note 9): use type custom with its actual overall area. Assemblies of single insulated conductors without an overall covering are not a cable (Note 9): enter them as individual conductors, not as one custom area.
  • Exact arithmetic: the fill percent is shown rounded up to 0.01 % and pass means the shown value is at or below the limit. Table 4 prints its percent columns rounded to 0.001 in2; this page takes the percent of the exact 100 % column.
  • Areas: Table 5 approximate (worst-case, Note 10) areas for THHN/THWN/THWN-2, XHHW/XHHW-2, THW/THW-2/THHW, RHH/RHW/RHW-2 (with and without outer covering) and Table 8 stranded bare. Compact stranding (Table 5A), fixture wires, and sizes under 14 AWG are not included.
  • Raceways: EMT (1/2-4), IMC, RMC (1/2-6), PVC-40 and PVC-80 (1/2-6), ENT (1/2-2), FMC (3/8-4), LFMC (3/8-4), LFNC-B (3/8-2). Not included: EMT 5 and 6 in. and IMC 5 and 6 in. (2023-labelled copies show them; not sourced twice), PVC types A and EB, LFNC-A and C, and other raceways. The count of identical conductors is shown up to 2000 only.
  • Not checked: ampacity and the 310.15(C)(1) adjustment (see the ampacity app), voltage drop, bends and pulling, jam ratio, box fill, wireways. Table 1 applies to complete raceway systems (Note 2).

Related apps

  • Voltage Drop
  • Power Factor Correction
  • Dwelling Service Load
  • Conductor Ampacity & Sizing
  • Transformer Size & Protection
  • All Electrical apps

Guides

  • How to calculate conduit fill under NEC 2023 Chapter 9
  • How to calculate voltage drop with NEC Chapter 9 tables
  • How to calculate box fill under NEC 2023 314.16
OTWapps
About Methods & references View plans Privacy Terms

Engineering aid only. Professional verification required.