OTWapps
OTWapps
All apps
HomeSearch
Civil / Site
Full Site and Stormwater DesignPeak Runoff (Rational Method)Stormwater Runoff (TR-55)Earthwork Cut & FillGutter Spread & Inlet CapacityOutlet Structure RatingRiprap Outlet ProtectionGrass-Lined Channel & SwaleADA Ramp SlopeStorm Pipe SizingCulvert Capacity & SizingDetention Pond RoutingOpen-Channel FlowPavement DesignVertical CurvesSanitary SewerParkingFire Service LineModified Rational DetentionLift StationFull Lift Station Design
Structural
Wind Main Frame (MWFRS)Wind Components & Cladding (C&C)Load CombinationsLive LoadsWood BeamWood ColumnJoist & Rafter SpanSteel BeamSteel ColumnSeismic Base ShearSpread FootingCantilever Retaining WallTruss AnalysisSign StructuresSnow LoadsWood Shear Wall & DiaphragmConcrete VolumeRebar Weight & QuantityConcrete BeamCrane Runway BeamHelical Piles and AnchorsSolar Roof AttachmentTilt-Up Wall PanelSolar Ground-Mount PileFence and Freestanding Wall Wind
Electrical
Voltage DropPower Factor CorrectionDwelling Service LoadLighting (Lumen Method)Conductor Ampacity & SizingTransformer Size & ProtectionAvailable Fault CurrentBox FillConduit FillMotor Branch CircuitGrounding Conductor SizingPhotometric Analysis & Lighting LayoutPV String SizingConductor Resistance and Impedance
Mechanical
Duct SizingExhaustVentilationPsychrometricsHydronic Pipe Pressure DropPump and Fan PowerNPSH Available
Plumbing
Water Supply SizingDrain Fixture UnitsStorm/Roof DrainGas Pipe SizingWater Heater SizingSump Pump SizingWater Hammer (Surge)Pipe Thermal Expansion and Loop
Fire Protection
Sprinkler K-FactorSprinkler Design Area & DemandHydrant Flow Test & Supply CurveFire Extinguisher PlacementOccupant Load
AboutPricingAccount

Fire Service Line Calculator NFPA 13 / NFPA 24 hydraulics to the base of the riser

NFPA 13 / NFPA 24 hydraulics to the base of the riser
This app is temporarily unavailable.
Detailed calculation inputs (segments, devices, meta, name)

Result

Result not calculated

Confirm the inputs and the method notes before using the result.

How this result was calculated

Inputs & units
Method & assumptions
References & limitations
Engineering aid only. Professional verification required. The method notes and tags on this page are the references this app cites.

By running a calculation you agree to the Terms of Use and Privacy Policy. Results are preliminary and must be verified by a licensed professional.

Your calculation

▤Result not calculatedComplete the inputs and review before calculating.

Downloads

Review inputs, calculation steps, and assumptions in one report.

Method, assumptions and limits (read before use)
  • What it checks: a single series fire service line from the water main (where the hydrant flow test applies) to the base of the sprinkler riser. Pressure available at the base of the riser = supply curve pressure at the total flow − pipe and fitting friction − device losses (backflow preventer, meter) − elevation. It is compared with the demand pressure you enter (from the separate sprinkler hydraulic calculation) plus the margin you require, and the margin is reported in psi and percent.
  • Friction: Hazen-Williams, p = 4.52 Q1.85 / (C1.85 d4.87) psi per foot (Q gpm, d the actual inside diameter in inches, NFPA 13 28.2.2.1). C by the material you choose, per NFPA 13 Table 28.2.4.8.1 (the result shows the one C used, with this citation); or enter your own C as c_factor in the segment (in the Detailed calculation inputs, give either material or c_factor, not both; an entered C is warned). The inside diameter has no default.
  • Fittings: equivalent length = count × NFPA 13 Table 28.2.3.1.1 value (feet of Schedule 40 steel at C = 120; 3/4 to 12 in; elbows, tee with the flow turned, gate, butterfly and swing check valves) × the C multiplier of NFPA 13 Table 28.2.3.2.1 for the C used (the result shows the multiplier applied) × (inside diameter / reference diameter)4.87 (reference: Schedule 40 bore, Schedule 30 at 8, 10 and 12 in, per ASME B36.10M; the result shows the reference diameter used). The bore correction keeps the fitting pressure loss the same as for the reference bore at the same C and flow (a larger bore gives a longer equivalent length but less friction per foot), so it adds no safety factor. A fitting the table does not list (n/l) is rejected: give the manufacturer length as extra_equivalent_length_ft. Straight-through flow in a tee has no loss. NFPA 24 has no equivalent-length table that this app found; the NFPA 13 table is applied to the service line.
  • Supply: from the flow test, P = Ps − (Ps − Pr)(Q/Qr)1.85, a straight line on N1.85 graph paper (drawn below). Residual must be below static. A total flow above the tested flow is an extrapolation and is warned. Elevation: 0.433 psi per foot; enter the base of the riser elevation minus the test gauge elevation (positive costs pressure).
  • Hose allowance: required, no default: enter gpm (0 is valid) or choose a hazard (total hose allowance per NFPA 13 Table 19.2.3.1.2; the result shows the one value used). By default every segment and device carries the total flow (conservative); set carries_hose_stream to false on one that sees only the sprinkler flow. The pressure needed at a yard hydrant is not checked.
  • Devices: manufacturer data only. loss_psi is used as entered at the flow it sees and does not change with flow, so for a meter or backflow preventer whose loss rises with flow enter its manufacturer curve instead; loss_curve [[gpm, psi], ...] is interpolated and must cover the flow. In the plotted curve only, a fixed loss is scaled with Q2.
  • Checks: the gating check is available pressure ≥ demand + required margin. Velocity (advisory limit default 20 ft/s, a practice value; NFPA 13 sets none), extrapolation beyond the tested flow, and a flow-test pressure drop under 10 % of static are advisory: they warn and never change the verdict.
  • Required, no default: the flow test, the elevation difference (enter 0 only if the base of the riser and the test gauge are at the same elevation; every 10 ft of rise costs 4.3 psi), the demand and the hose allowance. Defaults (each echoed in "defaults used" and warned): required margin 0 psi, velocity limit 20 ft/s. Edition: NFPA 13 (2022 edition table numbering as reproduced by public references; numbers differ in older editions, e.g. Table 23.4.4.7.1 for C values in the 2013/2016 editions): confirm against the edition adopted by your authority having jurisdiction.
  • Inputs are strict: numeric values must be numbers (text is rejected); misspelled or unknown fields are rejected with a suggestion; a null is rejected (leave the field out); numbers in meta must be below 1e15; labels are at most 80 characters; at most 30 segments and 20 devices. Results are engineering aids; a licensed engineer must review before sealing.
  • Out of scope: the sprinkler system hydraulic design itself, looped or gridded supplies and branching, fire pumps and tanks, pressure-reducing valves, flow-test procedure and pitot conversion, hydrant fire flow (ISO or IFC), water hammer, thrust restraint, pipe pressure ratings, and metric units.

Related apps

  • Full Site and Stormwater Design
  • Peak Runoff (Rational Method)
  • Stormwater Runoff (TR-55)
  • Earthwork Cut & Fill
  • Gutter Spread & Inlet Capacity
  • All Civil / Site apps

Guides

  • Sprinkler K-factor: Q = K√P, with the 7 psi minimum
OTWapps
About Methods & references View plans Privacy Terms

Engineering aid only. Professional verification required.