OTWapps
OTWapps
All apps
HomeSearch
Civil / Site
Full Site and Stormwater DesignPeak Runoff (Rational Method)Stormwater Runoff (TR-55)Earthwork Cut & FillGutter Spread & Inlet CapacityOutlet Structure RatingRiprap Outlet ProtectionGrass-Lined Channel & SwaleADA Ramp SlopeStorm Pipe SizingCulvert Capacity & SizingDetention Pond RoutingOpen-Channel FlowPavement DesignVertical CurvesSanitary SewerParkingFire Service LineModified Rational DetentionLift StationFull Lift Station Design
Structural
Wind Main Frame (MWFRS)Wind Components & Cladding (C&C)Load CombinationsLive LoadsWood BeamWood ColumnJoist & Rafter SpanSteel BeamSteel ColumnSeismic Base ShearSpread FootingCantilever Retaining WallTruss AnalysisSign StructuresSnow LoadsWood Shear Wall & DiaphragmConcrete VolumeRebar Weight & QuantityConcrete BeamCrane Runway BeamHelical Piles and AnchorsSolar Roof AttachmentTilt-Up Wall PanelSolar Ground-Mount PileFence and Freestanding Wall Wind
Electrical
Voltage DropPower Factor CorrectionDwelling Service LoadLighting (Lumen Method)Conductor Ampacity & SizingTransformer Size & ProtectionAvailable Fault CurrentBox FillConduit FillMotor Branch CircuitGrounding Conductor SizingPhotometric Analysis & Lighting LayoutPV String SizingConductor Resistance and Impedance
Mechanical
Duct SizingExhaustVentilationPsychrometricsHydronic Pipe Pressure DropPump and Fan PowerNPSH Available
Plumbing
Water Supply SizingDrain Fixture UnitsStorm/Roof DrainGas Pipe SizingWater Heater SizingSump Pump SizingWater Hammer (Surge)Pipe Thermal Expansion and Loop
Fire Protection
Sprinkler K-FactorSprinkler Design Area & DemandHydrant Flow Test & Supply CurveFire Extinguisher PlacementOccupant Load
AboutPricingAccount

Gutter Spread & Inlet Capacity Calculator FHWA HEC-22

FHWA HEC-22
This app is temporarily unavailable.

Result

Result not calculated

Confirm the inputs and the method notes before using the result.

How this result was calculated

Inputs & units
Method & assumptions
References & limitations
Engineering aid only. Professional verification required. The method notes and tags on this page are the references this app cites.

By running a calculation you agree to the Terms of Use and Privacy Policy. Results are preliminary and must be verified by a licensed professional.

Your calculation

▤Result not calculatedComplete the inputs and review before calculating.

Downloads

Review inputs, calculation steps, and assumptions in one report.

Method, assumptions and limits
  • Method: FHWA HEC-22 4th ed. (FHWA-HIF-24-006, Feb 2024): gutter flow and spread by Izzard (Eq 5.2), composite gutters (Eq 5.5 to 5.8), V-shaped roadside gutters (Example 5.3); inlet interception on grade (Eq 7.1 to 7.13, splash-over from Figure 7.8) and in sags (weir/orifice, Eq 7.14 to 7.21); clogging and bypass carryover down a series of inlets. US units (ft, in, cfs, fps).
  • Figure 7.8: the splash-over velocity Vo is read from a digitized copy of the chart: about +/-0.15 fps below 3 ft and about +/-0.3 fps from 3 to 4.5 ft, where the three middle curves converge and the 30-degree and 45-degree curves cannot be told apart with certainty (the P-1-7/8 family can be off by up to 0.35 fps at 0.5 ft). Enter your own Vo (tested or manufacturer value) to override it. Version 0.1.2 re-digitized the 45-degree tilt-bar, reticuline, curved-vane (4 to 4.5 ft) and 30-degree tilt-bar (3 to 4.5 ft) curves.
  • Sag capacity step: for a curb opening HEC-22 uses the lower of the weir and orifice flows between d + a = h and 1.4 h, and the orifice equation alone above 1.4 h (slotted inlet: 2 to 5 in, then orifice). The capacity never decreases with depth, but it is not continuous at 1.4 h (5 in): it steps up there when the orifice flow is above the weir flow (for a depressed opening typically 15 % and up to 70 % or more; for an undepressed one about 4 %). HEC-22 gives no transition above that point, so the numbers are not smoothed; one depth is reported for every flow inside the step, and a warning gives the size of the step and the depth that continuing the lower-of-weir-and-orifice rule would give.
  • Inputs are strict: unknown or misspelled fields are rejected with a suggestion; a null is rejected in the case, gutter and inlet objects (leave the field out), but a null value inside meta (free-form project information, never used in a calculation) is accepted; an inlet.grate / curb / slot object that the chosen inlet type does not use is rejected, not ignored; location, section and clog_scope must be one of their listed words; labels are at most 80 characters and meta at most 20 entries; lengths, widths, slopes and coefficients are range-checked; fields that do not apply to the chosen section are listed in the warnings. A curb depression a_in that is not less than the opening height h_in is flagged. Clogging is an input you must choose (a sag result with none entered is the UNCLOGGED capacity).
  • Not modeled: flow in the street beyond the gutter section (inverted crown, median ditches), grate or curb inlets with other geometries, inlet-to-inlet interference other than the carryover, pavement ponding hydraulics beyond the allowable spread, and hydroplaning checks. A spread above 40 ft is flagged as implausible. Engineering aid only. Professional verification required.

Related apps

  • Outlet Structure Rating
  • Riprap Outlet Protection
  • Grass-Lined Channel & Swale
  • Storm Pipe Sizing
  • Culvert Capacity & Sizing
  • All Civil / Site apps

Guides

  • Rational Method peak runoff (Q = CiA) with a worked example
OTWapps
About Methods & references View plans Privacy Terms

Engineering aid only. Professional verification required.