How to calculate conduit fill under NEC 2023 Chapter 9
Step-by-step NEC 2023 conduit fill: Chapter 9 Table 1 fill percentages, Table 4 conduit areas, Table 5 wire areas, the 0.8 rounding rule, and a worked EMT example.
Run this in the free Conduit Fill appConduit fill limits how much of a raceway's inside area the conductors may occupy, so that wire can be pulled without damaging insulation and heat can escape. In the NEC the rules sit in Chapter 9: Table 1 gives the allowed percentage, Table 4 gives the inside area of each raceway type and trade size, and Table 5 gives the area of each insulated conductor.
Step 1: Pick the fill percentage (Chapter 9, Table 1)
| Number of conductors | Maximum fill |
|---|---|
| 1 | 53% |
| 2 | 31% |
| Over 2 | 40% |
Equipment grounding and bonding conductors count toward fill (Chapter 9, Note 3). A nipple 24 in. or shorter between boxes may be filled to 60% (Note 4).
Step 2: Look up the raceway area (Table 4)
Table 4 lists the total inside area and the 40% area for each raceway type. Use the table for the raceway you are installing, because EMT, IMC, rigid, PVC Schedule 40 and Schedule 80 all have different inside diameters at the same trade size. For EMT, the total areas are 0.304 in.² (1/2 in.), 0.533 in.² (3/4 in.) and 0.864 in.² (1 in.).
Step 3: Add up the conductor areas (Table 5, or Table 8 for bare wire)
Table 5 gives the approximate area of each insulated conductor by insulation type and size. For THHN/THWN-2: 14 AWG 0.0097 in.², 12 AWG 0.0133 in.², 10 AWG 0.0211 in.², 8 AWG 0.0366 in.². Bare conductors use the area in Table 8.
Step 4: Compare
Fill is acceptable when the total conductor area is no more than the allowed percentage of the raceway area.
Worked example: four 10 AWG THHN in 1/2 in. EMT
- Three current-carrying 10 AWG THHN plus one 10 AWG THHN equipment grounding conductor: 4 conductors, so 40% applies.
- Conductor area: 4 × 0.0211 = 0.0844 in.²
- Allowed: 40% × 0.304 = 0.122 in.²
- 0.0844 ≤ 0.122, so the fill is acceptable (about 28% of the conduit's area).
How many wires of one size fit? The 0.8 rule
When every conductor is the same size, divide the allowed area by one conductor's area. Chapter 9 Note 7 lets you round up to the next whole number only when the decimal is 0.8 or more. For 12 AWG THHN in 3/4 in. EMT: 0.213 / 0.0133 = 16.02, so 16 conductors. In 1/2 in. EMT: 0.122 / 0.0133 = 9.14, so 9. These match the Informative Annex C tables, which do this math for same-size conductors.
Common mistakes
- Forgetting to count the equipment grounding conductor.
- Using the EMT area for PVC or rigid conduit at the same trade size.
- Using Annex C for mixed wire sizes; Annex C only covers conductors of one size and type.
- Treating fill as the only limit. Ampacity adjustment for more than three current-carrying conductors (310.15(C)(1)) and bending space can control first.
Run it in the app
The free Conduit Fill app does this calculation in your browser, shows each intermediate value and cites the code section on each line. You can try 3 calculations without an account. A free account is needed after that, and to download results.
Frequently asked questions
What is the 40% conduit fill rule?
NEC Chapter 9 Table 1 limits conductors to 40% of the raceway's inside area when there are more than two conductors. One conductor may use 53% and two conductors 31%.
Do ground wires count in conduit fill?
Yes. Chapter 9 Note 3 requires equipment grounding and bonding conductors to be included in the fill calculation, using their actual area.
Can I round up the number of wires?
Only when all conductors are the same size and the calculated number has a decimal of 0.8 or more (Chapter 9 Note 7).
References
NFPA 70, National Electrical Code, 2023 edition: Chapter 9 Tables 1, 4, 5 and 8, and Chapter 9 Notes to Tables. Values above are quoted for illustration; check them against the edition adopted in your jurisdiction.
Related apps
More guides
- How to calculate voltage drop with NEC Chapter 9 tables
- ASCE 7-22 velocity pressure and components and cladding pressure: a worked example
- Rational Method peak runoff (Q = CiA) with a worked example
- Sprinkler K-factor: Q = K√P, with the 7 psi minimum
- How to calculate box fill under NEC 2023 314.16
Published 2026-11-12.